# Under Desk Cable Management: How to Route and Hide Cables Properly
> A step-by-step guide to under desk cable management — cable trays, raceways, velcro ties, power strip mounting, and how to do it cleanly the first time.
**Category:** Storage & Cable Management  
**Primary keyword:** under desk cable management  
**Published:** 2026-05-12  
**Last reviewed:** 2026-05-12  
**Parent pillar:** home-office-cable-management  
**Canonical URL:** https://smallhomeofficeideas.site/under-desk-cable-management/  
**Markdown URL:** https://smallhomeofficeideas.site/under-desk-cable-management/index.md
## Related Guides
- small-home-office-setup
- desk-cable-management
- cable-management-ideas
- minimalist-home-office-setup
---
Under-desk cable management works by moving the mess from the floor and desk surface to the underside of the desk — where it is hidden when you sit and invisible in most room views. Done correctly, the only cable visible from the front of the desk is a single power lead running to the wall outlet. For the full three-zone approach that covers the desk surface and floor as well, see the [home office cable management guide](/home-office-cable-management/).

## What you need before starting

## Step-by-step: setting up under-desk cable management

Before starting, confirm your desk has enough depth and a flat back edge to mount the tray — the [home office desk setup guide](/home-office-desk-setup/) covers what to check before adding under-desk accessories. Then follow these steps:

**Step 1 — Label every cable before you unplug anything.** Use a label or a loop of tape with the device name written on it. Do both ends: the device end and the power/data end. This takes five minutes and saves significant frustration later.

**Step 2 — Mount the cable tray.** Position the tray under the desk surface toward the back, centred or offset to where the power outlet is. Most trays mount with four screws into the underside of the desk. On hollow-core or thin desks, use the tray's widest mounting plate to distribute the load.

**Step 3 — Mount the power strip inside the tray.** Most cable trays are sized to hold a standard power strip. Secure it with the strip's mounting holes if available, or use a velcro strap through the tray slots. The power strip stays permanently in the tray — you only run one cable from the tray to the wall outlet.

**Step 4 — Route device cables to the tray.** Run each device cable (monitor power, laptop charger, USB hub, etc.) from the device, along the desk surface or back channel, down the rear desk leg, and into the tray. Keep excess cable length inside the tray — do not let it pile on the floor.

**Step 5 — Bundle cables on each desk leg.** Group the cables running down each leg and wrap them with velcro ties every 15–20 cm. One bundle per leg, not individual cables.

**Step 6 — Run one cable from tray to wall.** The only cable that needs to reach the wall outlet is the power strip's lead. Route it along the baseboard or use a wall cable raceway to keep it off the floor.

## Under-desk mounting options compared

## Cable tray sizing

Cable trays come in widths from 30 to 90 cm. Choose based on your power strip length and how many cables you need to store.

- **30–40 cm:** Suits a 4-outlet power strip and 3–4 device cables. Enough for a laptop-only setup.
- **50–60 cm:** Standard for a single monitor setup with 5–7 device cables.
- **70–90 cm:** For dual monitor setups, desktop computers, or 8+ cables. Mount across the full desk width.

Most trays are 10–15 cm deep. Depth matters if your power strip is wide or if you need to coil excess cable inside the tray.

## The floor-to-wall cable problem

The one cable that always remains visible is the power strip lead running from under the desk to the wall outlet. For more solutions to specific desk cable problems, see [cable management ideas](/cable-management-ideas/). Three ways to handle the floor-to-wall cable cleanly:

**Wall cable raceway:** A plastic channel that adheres to the baseboard and hides the cable inside. Paintable versions blend into skirting boards. Most effective but requires measuring and cutting to fit.

**Cable sleeve:** A fabric or plastic sleeve that gathers the cable close to the wall and tucks it against the baseboard. No tools, no adhesive. Less clean-looking than a raceway but faster.

**Floor cable channel:** A flat rubber or plastic channel that sits on the floor and covers cables crossing open space. Best for desks not positioned against a wall.